Images and specifications show a representative configuration. Final equipment details and delivery schedule are confirmed after your requirements are reviewed.图片与参数展示代表性配置;最终设备细节与交付安排将在需求评审后确认。
Low-level powered transfer低位动力输送
Design the roller layout around the load base and every transfer point.根据载荷底面和每个交接点设计滚筒布局
A FORTRAN powered floor roller conveyor moves supported panel loads between nearby furniture-production stations at a low transfer height. Also called a low-level roller conveyor or ground roller conveyor, it provides driven transfer rather than relying on manual pushing. The FQ-DG0625 reference is one conveyor configuration; select the roller layout from the load underside and the handover to a lift table, loading station or adjoining conveyor.FORTRAN 动力地滚输送线在较低交接高度下,于相邻家具生产工位之间输送有稳定支承底面的板件载荷,也称低位动力滚筒输送线。该设备采用动力移送,而非依靠人工推送。FQ-DG0625 是其中一种参考配置,滚筒布置需根据载荷底面,以及升降台、上料工位或相邻输送段的交接条件选择。
01
Best fit when适合这些情况
Repeatable powered transfer between defined production stations.在明确的生产工位之间进行可重复的动力输送。
Panel stacks or supported loads whose underside can bridge the selected roller spacing.底面能够跨越所选辊距的板垛或有支撑载荷。
Layouts that need controlled start, stop and handover instead of manual pushing.需要受控启停与交接、而不是人工推送的布局。
02
Process role工序如何衔接
01Receive the load squarely on the agreed roller width and transfer height.按约定的滚筒宽度和输送高度平稳接收载荷。
02Move the load through the powered section with the agreed controls and stopping logic.按照约定的控制与停止逻辑,通过动力段输送载荷。
03Hand the load to the next conveyor, workstation or handling device.将载荷交接给下一段输送、工位或搬运设备。
03
Send for configuration选型报价请提供
Load length, width, height, weight and supporting underside.载荷长/宽/高、重量及承载底面。
Required conveyor length, clear width, transfer height and line direction.所需输送长度、有效宽度、输送高度和产线方向。
Roller spacing requirement, stopping positions and accumulation logic.辊距要求、停止位置和缓存逻辑。
Upstream and downstream interfaces, controls, guarding and operator routes.前后道接口、控制、安全防护及人员通道。
Scope boundary供货边界
“Floor-level” describes a low transfer arrangement; it does not by itself define installation method, safe load capacity or compatibility with a trolley or pallet. These details must be stated in the layout and proposal.“地辊式”表示低位输送布置,并不自动确定安装方式、安全载荷,也不代表一定兼容某种台车或托盘;这些条件必须在布局和方案中明确。
Acceptance focus验收重点
Run representative loads across every handover and stopping point. Check support, tracking, start and stop behaviour, clearance, controls and recovery after an interruption.使用代表性载荷通过每个交接点与停止位,检查支撑、运行轨迹、启停表现、净空、控制以及中断后的恢复。
Reference configuration: FQ-DG0625 in the 2025 FORTRAN catalogue. Conveyor dimensions and roller spacing do not establish load capacity or suitability for a particular pallet. Confirm support, weight and each receiving interface for the proposed installation.参考配置:2025 年 FORTRAN 画册中的 FQ-DG0625。输送尺寸和辊距不能证明承载能力或适配某种托盘;应按拟安装方案核对支承、重量及各接料接口。
Length × width × height长 × 宽 × 高
3000 × 800 × 300 mm3000 × 800 × 300 mm
Roller spacing滚筒间距
200 mm200 mm
Equipment names and purchasing decisions采购名称与工序确认
Is a roller table conveyor the same as a powered roller conveyor?动力辊台、辊道输送机和无动力滚筒输送机有什么区别?
A roller table conveyor describes the supporting and conveying surface. A motor driven powered roller conveyor moves the load using a drive, while a non driven roller conveyor needs an agreed manual or gravity-assisted transfer method. FORTRAN offers powered and unpowered roller conveyors for panels. Compare the supporting underside, roller pitch, transfer height and stopping arrangement before choosing the drive. Floor-level placement describes the layout height, not the source of movement.“辊道输送机”或“滚筒输送机”描述以辊筒承托物料的设备;动力辊台带有驱动,无动力滚筒输送机也称无动力辊道输送机,需要明确人工推送或经评估的重力移送方式。富全提供相应的板材输送配置。比较时先核对底面支撑、辊距、交接高度与停止方式,再选择驱动,不能把低位地滚布置直接等同于无动力。
How does roller pitch affect panel stacks and furniture cartons?地滚输送线的辊筒间距,为什么要同时核对小板、板垛和纸箱?
Roller pitch is the spacing between neighbouring roller centres. A roller conveyor needs sufficient support under the shortest load and at each transfer gap. Test the bottom panel of a bare stack, the runners of a pallet and the underside of a loaded carton as different support cases. For a FORTRAN panel transfer unit, provide the smallest footprint, load distribution, travel direction and receiving surface. Confirm transitions and stopping with representative loads instead of choosing the spacing from total weight alone.辊筒间距即相邻辊筒中心之间的距离。滚筒输送线要让最短物料及跨越交接缝隙的物料获得足够支撑。裸板垛底板、托盘底梁和装件纸箱底面属于不同工况,应分别试验。富全移载输送单元选型需要最小底面尺寸、重量分布、移动方向和接料表面,并使用代表性载荷确认过渡及停止,不能只按总重量选择辊距。
Related purchasing terms: powered floor roller conveyor; low-level roller conveyor for panels; furniture factory powered ground conveyor. Confirm the operating method and supplied equipment against the configuration on this page.相关采购叫法:动力地滚输送线、低位板材辊筒输送、家具工厂动力地辊线。请结合本页配置确认操作方式与供货设备范围。
Buyer questions采购常见问题
Questions to settle before choosing this equipment.选型前需要确认的问题
Is a floor roller conveyor the same as a gravity roller conveyor?地滚输送线等于无动力滚筒线吗?
No. Floor-level describes a low transfer height, while powered or unpowered describes the drive. This page covers powered rollers. An unpowered line needs an agreed manual or gravity-assisted movement method, and gravity movement requires controlled stopping. Choose the drive and height separately.不是。地滚描述较低的输送高度,动力或无动力描述驱动方式。本页为动力滚筒。无动力线需要明确人工或重力辅助移送方法,依靠重力还需要受控停止。驱动方式与高度应分别选择。
Can the conveyor move panel stacks or pallets?这条输送线可以输送板垛或托盘吗?
Assess the supporting underside, load distribution, weight and orientation against the roller pitch and each handover gap. A pallet may not bridge the rollers in every orientation. The FQ-DG0625 dimensions do not state a universal load rating or pallet compatibility; agree the supported load with drawings and samples.需按辊距和每处交接间隙核对承载底面、载荷分布、重量及朝向。托盘不一定能以任意方向跨越滚筒。FQ-DG0625 的外形尺寸不能证明通用承载或托盘适配性,应结合图纸和样件确认承载对象。
What is needed to connect a low-level conveyor to a lift table or gantry?低位输送线连接升降台或龙门需要哪些条件?
Agree transfer height, direction, stopping position and the load support across the gap. Define which device permits movement, what happens when the receiver is occupied and how the line restarts after a stop. Include operator access and guarding in the layout; these controls are project requirements, not automatic inclusions in a bare conveyor.需约定交接高度、方向、停止位置及间隙处的载荷支承,明确哪台设备发出移载放行、接料位占用时如何处理以及停机后怎样恢复。布局应纳入人员通道和防护;这些控制属于项目要求,不是裸输送段默认包含的功能。
Is this the right solution for your production line?这项方案是否适合您的产线?
Send your workpiece sizes, target output, current machine model and destination country so we can review line compatibility and configuration options.请提供工件尺寸、目标产能、现有设备型号和目的国家,以便评估产线适配性与可选配置。