3-Ton E-Type Lifting Table
Lifting tables板材液压升降台

3-Ton E-Type Lifting Table3 吨 E 型升降台

Uses an E-shaped platform to lift loads up to 3 tonnes while leaving access for pallet trucks or handling equipment.采用E型台面升降不超过3吨的载荷,同时为托盘车或搬运设备保留作业空间。

Read product details in Chinese →查看中文设备资料与选型 →
Ask on WhatsAppWhatsApp 咨询

Your contact and a short message are enough to start.留下联系方式和一句需求,即可开始沟通。

Brand品牌FORTRANFORTRAN
Manufacturing location生产基地Foshan, Guangdong, China中国广东佛山
Configuration配置方式Project-specific configuration按项目需求配置
Images and specifications show a representative configuration. Final equipment details and delivery schedule are confirmed after your requirements are reviewed.图片与参数展示代表性配置;最终设备细节与交付安排将在需求评审后确认。

Check the load carrier and entry geometry before choosing an E-type table.选择 E 型升降台前,先核对载具与进叉几何条件

Best for loads that need low-level pallet-truck access and controlled hydraulic lifting at a handling station. The reference configuration lists a load up to 3,000 kg, but the selected working range and open platform must also match the pallet or carrier footprint.适合需要手动液压车低位进入,并在搬运工位进行受控液压升降的载荷。参考配置列出的载荷为不超过 3,000 kg;所选工作范围和开放式平台还必须匹配托盘或载具底面。

01

Best fit when适合这些情况

  • Palletised or supported loads with compatible pallet-truck entry.与液压车进叉方式兼容的托盘或有支撑载荷。
  • Stations that need a low collapsed height without a conventional deep pit.需要较低收合高度、且不采用常规深地坑的工位。
  • Applications where the carrier footprint and load centre can be defined.能够明确载具底面和载荷重心的应用。
02

Process role工序如何衔接

  1. 01Enter the open platform with the agreed pallet truck and load carrier.使用约定液压车和载具进入开放式平台。
  2. 02Set the load down on the defined supporting points and withdraw the truck.将载荷放置在明确支撑点上,并退出液压车。
  3. 03Lift to the required working height, then reverse the sequence for removal.升至所需工作高度,取料时按相反顺序操作。
03

Send for configuration选型报价请提供

  • Maximum and normal load, centre of gravity and load distribution.最大及常用载荷、重心和载荷分布。
  • Pallet or carrier drawing, pallet-truck fork width, length and wheel path.托盘或载具图、液压车叉宽、叉长和轮路。
  • Required platform footprint, lowest height and highest working height.所需平台占地、最低高度和最高工作高度。
  • Floor condition, duty cycle, operator route, controls and guarding.地面条件、工作频率、人员路线、控制和安全防护。
Scope boundary供货边界

An E-shaped opening does not mean every pallet truck, pallet or fork arrangement will fit. Capacity, entry clearances, support points and installation must be confirmed on the selected drawing.E 型开口不代表适用于所有液压车、托盘或叉位组合。承载、进入净空、支撑点和安装方式必须在所选图纸上确认。

Acceptance focus验收重点

Use the agreed pallet truck, carrier and representative load to test entry, set-down, full lift, stability, removal, controls, guarding and emergency lowering.使用约定液压车、载具和代表性载荷,测试进入、放置、全程升降、稳定性、取走、控制、安全防护和紧急下降。

Core specifications.核心参数

Use these reference specifications as a starting point. Send your workpiece range, line layout and target output to confirm the configuration.以下参数可作为选型参考。请提供工件范围、产线布局和目标产能,以便确认配置。

Maximum load最大载荷
≤ 3000 kg≤ 3000 kg

Equipment names and purchasing decisions采购名称与工序确认

How do industrial lift tables differ from a roller transfer station?液压升降台、滚筒升降机和动力输送辊台如何配合?

A hydraulic lifting table changes the supported load height. Adding rollers provides a horizontal transfer surface; adding powered rollers introduces driven movement and an interface with neighbouring equipment. A conveyor at a fixed height does not provide the same lifting function. For furniture panel stacks, specify load distribution, low and high working positions, travel, pallet support and fork access as separate requirements.液压升降台负责调整载荷高度,滚筒升降机在升降台面上增加水平移载条件;有动力滚筒台面还需要驱动和相邻设备的联动。固定高度的动力输送辊台不能代替升降功能。家具板垛项目应分别列出载荷分布、最低及最高作业位置、升降行程、托盘支撑和叉车进入条件。

Compare equipment and quotation requirements比较相关设备与询价条件 →

How should a lifting table hand over a complete panel stack?升降平台与地滚线交接整垛板材,怎样核对承载和高度?

A lifting table changes the working height, while the selected top determines how the load is transferred. For complete stack handling, provide the total weight including its load carrier, centre of gravity and supporting underside. Agree the transfer level, available travel, stops and receiving conveyor with FORTRAN. Test loading, lifting, alignment and unloading as one sequence. Lift-tables with roller tops and fixed-top tables perform different transfer tasks; neither the nominal load nor the platform size alone establishes a suitable handover.升降平台调整作业高度,台面形式决定如何移载。整垛板材交接时,需要提供含托盘或工装的总重量、重心与承载底面,并与富全确认交接高度、可用行程、止挡及接料输送段。把装载、升降、对齐和卸载作为完整过程试验。滚筒台面与固定台面的移载任务不同,额定载荷或台面尺寸都不能单独证明交接适用。

Compare equipment and quotation requirements比较相关设备与询价条件 →

Names used for this equipment这款设备的采购叫法

Related purchasing terms: E-shaped hydraulic lift table; pallet-truck-access lifting platform; E-type material handling lift. Confirm the operating method and supplied equipment against the configuration on this page.相关采购叫法:E型液压升降平台、托盘车进出式升降台、E形物料升降台。请结合本页配置确认操作方式与供货设备范围。

Questions to settle before choosing this equipment.选型前需要确认的问题

What is this equipment used for?3 吨 E 型升降台有什么用途?

It uses an E-shaped platform to lift loads up to 3 tonnes while leaving access for pallet trucks or handling equipment.采用E型台面升降不超过3吨的载荷,同时为托盘车或搬运设备保留作业空间。

What affects the price of this equipment?3 吨 E 型升降台的价格受哪些因素影响?

The price and machine scope depend on load and center of gravity, platform size, travel height, top transfer surface, forklift access, pit and duty cycle. A useful quotation should state the operating range, included equipment and project responsibilities instead of giving one price for different configurations.3 吨 E 型升降台的价格和设备范围取决于载荷及重心、平台尺寸、升降行程、顶部移载形式、叉车位、地坑和工作频率。有效报价应说明运行范围、包含设备和项目责任,不能用一个价格代表不同配置。

What information should I send for a quotation?询问3 吨 E 型升降台报价时需要提供什么?

Send load and center of gravity, platform size, travel height, top transfer surface, forklift access, pit and duty cycle, plus photos or drawings of the available area and any equipment that must connect to the new machine. These details help the supplier propose a configuration that fits your project.请提供载荷及重心、平台尺寸、升降行程、顶部移载形式、叉车位、地坑和工作频率,并附可用场地照片或图纸,以及需要连接的现有设备资料,便于制造商或供应商按照实际项目提出方案。

How should I compare equipment suppliers?如何比较3 吨 E 型升降台制造商和供应商?

Ask each company to respond to the same requirement brief. Compare the proposed configuration, stated limits, layout, controls and interfaces, acceptance method, documentation, delivery scope, installation responsibilities and after-sales support.建议让每家公司按照同一份需求资料回复,并比较建议配置、明确限制、布局、控制与接口、验收方法、技术文件、交付范围、安装责任和售后支持。

Project enquiry项目咨询

Is this the right solution for your production line?这项方案是否适合您的产线?

Send your workpiece sizes, target output, current machine model and destination country so we can review line compatibility and configuration options.请提供工件尺寸、目标产能、现有设备型号和目的国家,以便评估产线适配性与可选配置。

Ask on WhatsAppWhatsApp 咨询
No app or email client required

Get a quick quote

Leave a contact method and one sentence about what you need so we can discuss your project.

Current pageGeneral website enquiry
Choose more than one if needed. Quick text is added without replacing your own message.