Raises panel loads up to 1 tonne and aligns its roller surface with adjacent conveyors for controlled height transfer.可升降不超过1吨的板材载荷,并使滚筒台面与相邻输送线对接,实现受控高度转运。
Images and specifications show a representative configuration. Final equipment details and delivery schedule are confirmed after your requirements are reviewed.图片与参数展示代表性配置;最终设备细节与交付安排将在需求评审后确认。
Roller-top height transfer滚筒台面高度转接
Coordinate the lift range and roller handover as one transfer station.把升降范围与滚筒交接作为一个转运工位统一确认
Best for supported panel loads that need vertical adjustment before manual or conveyor handover. The reference configuration lists a load up to 1,000 kg and a 300–1,100 mm working-height range; final selection still depends on load distribution, platform width and the adjoining transfer surface.适合在人工或输送交接前需要调节高度的有稳定支撑板件载荷。参考配置列出的载荷为不超过 1,000 kg,工作高度范围为 300–1,100 mm;最终选型仍需结合载荷分布、平台宽度和相邻移载表面确认。
01
Best fit when适合这些情况
Panel stacks that must align with a roller conveyor or handling station.需要与滚筒线或搬运工位对接的板垛。
Layouts that need a low receiving position and a higher transfer position.需要低位接料和较高交接位置的布局。
Loads whose supporting underside can bridge the selected roller spacing.承载底面能够跨越所选辊距的载荷。
02
Process role工序如何衔接
01Receive the load squarely on the agreed roller surface.在约定的滚筒台面上平稳接收载荷。
02Raise or lower the table to the required working or transfer height.将平台升降至所需操作或交接高度。
03Move the load across the aligned rollers using the agreed transfer method.按照约定移载方式,通过已对齐的滚筒完成交接。
03
Send for configuration选型报价请提供
Maximum and normal load, centre of gravity and supporting underside.最大及常用载荷、重心和承载底面。
Required table length and width, lowest height and highest height.所需台面长/宽、最低高度和最高高度。
Roller spacing, transfer direction, adjoining conveyor and stopping position.辊距、移载方向、相邻输送设备和停止位置。
Duty cycle, controls, guarding, installation surface and operator access.工作频率、控制、安全防护、安装地面和人员通道。
Scope boundary供货边界
A roller top provides a transfer surface; it does not establish powered movement unless a drive is included in the proposal. The 1-ton reference rating also does not cover every off-centre or poorly supported load.滚筒台面提供移载表面,并不代表配置了动力输送,只有方案明确列出驱动时才包含。1 吨参考承载也不代表适用于所有偏载或支撑不足的载荷。
Acceptance focus验收重点
Test representative loads through the full height range and every handover. Check stability, roller support, alignment, stopping, controls, guarding and recovery after interruption.使用代表性载荷完成全高度范围及每个交接点测试,检查稳定性、滚筒支撑、对中、停止、控制、安全防护和中断恢复。
Use these reference specifications as a starting point. Send your workpiece range, line layout and target output to confirm the configuration.以下参数可作为选型参考。请提供工件范围、产线布局和目标产能,以便确认配置。
Maximum load最大载荷
≤ 1000 kg≤ 1000 kg
Height travel升降行程
300–1100 mm300–1100 mm
Table size台面尺寸
2500 × 600/730/800 mm2500 × 600/730/800 mm
Equipment names and purchasing decisions采购名称与工序确认
How do industrial lift tables differ from a roller transfer station?液压升降台、滚筒升降机和动力输送辊台如何配合?
A hydraulic lifting table changes the supported load height. Adding rollers provides a horizontal transfer surface; adding powered rollers introduces driven movement and an interface with neighbouring equipment. A conveyor at a fixed height does not provide the same lifting function. For furniture panel stacks, specify load distribution, low and high working positions, travel, pallet support and fork access as separate requirements.液压升降台负责调整载荷高度,滚筒升降机在升降台面上增加水平移载条件;有动力滚筒台面还需要驱动和相邻设备的联动。固定高度的动力输送辊台不能代替升降功能。家具板垛项目应分别列出载荷分布、最低及最高作业位置、升降行程、托盘支撑和叉车进入条件。
How should a lifting table hand over a complete panel stack?升降平台与地滚线交接整垛板材,怎样核对承载和高度?
A lifting table changes the working height, while the selected top determines how the load is transferred. For complete stack handling, provide the total weight including its load carrier, centre of gravity and supporting underside. Agree the transfer level, available travel, stops and receiving conveyor with FORTRAN. Test loading, lifting, alignment and unloading as one sequence. Lift-tables with roller tops and fixed-top tables perform different transfer tasks; neither the nominal load nor the platform size alone establishes a suitable handover.升降平台调整作业高度,台面形式决定如何移载。整垛板材交接时,需要提供含托盘或工装的总重量、重心与承载底面,并与富全确认交接高度、可用行程、止挡及接料输送段。把装载、升降、对齐和卸载作为完整过程试验。滚筒台面与固定台面的移载任务不同,额定载荷或台面尺寸都不能单独证明交接适用。
Related purchasing terms: roller-deck panel lift table; panel stack roller lifting platform; conveyor height matching lift. Confirm the operating method and supplied equipment against the configuration on this page.相关采购叫法:滚筒台面板材升降台、板垛滚筒升降平台、输送线高度对接升降台。请结合本页配置确认操作方式与供货设备范围。
Buyer questions采购常见问题
Questions to settle before choosing this equipment.选型前需要确认的问题
What is this equipment used for?1 吨固定式滚筒升降台有什么用途?
It raises panel loads up to 1 tonne and aligns its roller surface with adjacent conveyors for controlled height transfer.可升降不超过1吨的板材载荷,并使滚筒台面与相邻输送线对接,实现受控高度转运。
What affects the price of this equipment?1 吨固定式滚筒升降台的价格受哪些因素影响?
The price and machine scope depend on load and center of gravity, platform size, travel height, top transfer surface, forklift access, pit and duty cycle. A useful quotation should state the operating range, included equipment and project responsibilities instead of giving one price for different configurations.1 吨固定式滚筒升降台的价格和设备范围取决于载荷及重心、平台尺寸、升降行程、顶部移载形式、叉车位、地坑和工作频率。有效报价应说明运行范围、包含设备和项目责任,不能用一个价格代表不同配置。
What information should I send for a quotation?询问1 吨固定式滚筒升降台报价时需要提供什么?
Send load and center of gravity, platform size, travel height, top transfer surface, forklift access, pit and duty cycle, plus photos or drawings of the available area and any equipment that must connect to the new machine. These details help the supplier propose a configuration that fits your project.请提供载荷及重心、平台尺寸、升降行程、顶部移载形式、叉车位、地坑和工作频率,并附可用场地照片或图纸,以及需要连接的现有设备资料,便于制造商或供应商按照实际项目提出方案。
How should I compare equipment suppliers?如何比较1 吨固定式滚筒升降台制造商和供应商?
Ask each company to respond to the same requirement brief. Compare the proposed configuration, stated limits, layout, controls and interfaces, acceptance method, documentation, delivery scope, installation responsibilities and after-sales support.建议让每家公司按照同一份需求资料回复,并比较建议配置、明确限制、布局、控制与接口、验收方法、技术文件、交付范围、安装责任和售后支持。
Is this the right solution for your production line?这项方案是否适合您的产线?
Send your workpiece sizes, target output, current machine model and destination country so we can review line compatibility and configuration options.请提供工件尺寸、目标产能、现有设备型号和目的国家,以便评估产线适配性与可选配置。